|
|
Zetec history guide
| Contents: |
|
Intro
Development
Fiesta compatibility
| |
|
Intro
The Ford CVH engine has been around for 20 odd years in one incarnation or another, and even the most recent Turbocharged EFI unit in the FRST is knocking on 13. In that time tuners have pushed the limits, extracting more and more power from it's 1600cc with Hybrid turbos, big valve heads and wild cams. For years the CVH engined cars ruled the roost as the tuneable hot hatch to have. When Ford killed off the Escort and Fiesta RS Turbos in the early 1990s and the CVH engine deceased, it seemed that a golden era had come to an end. Gone were the blown hemisphericals and in there place we were offered quiet, refined, normally aspirated 16v engines. Designed for power these lumps seemingly offered very little tuning potential and the new RS range was disregarded as boring and uninspiring. Little did people know what these engines were capable of...
The Zetec engines were launched in 1992 and within a few years had become available in several displacements:
- 1.6 90ps (89bhp) - used in the Fiesta Si and Ghia and some Escorts.
- 1.8 105ps (104bhp) - used in the Fiesta XR2i 16v and some Escorts.
- 1.8 115ps (113bhp) - used in some XR3is, Escort GTis and also found in all 1800 Mondeos.
- 1.8 130ps (128bhp) - used in the Fiesta RS1800 and some Escorts. The difference in power output comes from different profile cams, a larger throttle body and a different ECU map.
- 2.0 130ps (128bhp) - only used in the Mondeo.
Development
The Zetec was based on a strengthened CVH, with several key improvements - the most notable being the 16 valve head and twin cams. Improvements to the bottom end included a fully counterbalanced crank, larger capacity oil pump and on the 1.8 130ps and 2.0 models, oil jet sprays to provide under-piston cooling. There are three series' of Zetecs, not counting the newer small capacity 1.25, 1.4, 1.6 and 1.7 Yamaha co-produced Zetec-SE units:
- 1992 Series 1 - distinguishable by the "DOHC 16v" lettering embossed on the cam cover. Early Series 1's suffered from teething problems including sticking valves.
- 1995 Series 2 - distinguishable by "Zetec 16v" lettering embossed on the cam cover. Minor revisions to aleviate sticking valve problems. Also improvements to spark plugs, injectors, gaskets and cosmetics.
- 1998 Series 3 - the current model Zetec, as used in the Focus and Mondeo. A very different engine to the earlier Zetecs, both visually with it's black plastic cam cover, and internally. Starting at the top, the Series 3 features new injectors - end fed unlike the side fed units on the S1 and S2, and with a twin jet spray pattern. Solid tappets with adjustment shims replaced the hydraulic predecessors and the cam belt timing tensioning setup has been revised. The pistons are teflon coated to reduce friction, and the bearing caps are on a single piece frame to increase strength. The water pump was of a new outboard design, with large vanes for improved flow. The block was strengthened - a larger amount of metal between the bores is clearly visible in comparison with the S1 and S2. The oil filter mounting became integral to the base of the block and the sump gained a windage tray and baffles to reduce oil surge. The sump's webbing was also improved in an effort to combat block flex.
Fiesta compatability
The 1.6 and 1.8 Fiesta units are a direct fit, as you'd expect. The 2.0 Series 1 and 2 will fit, but require several modifications. The Series 3 requires new mounts fabricating, plus wiring loom modifications and re-routing of hoses.
For more information on the fitting and tuning of these engines, please select a link on the right.
|
| Disclaimer: Please note that the information contained in this article is intended only for guidance purposes and you should always consult an experienced tuner before shelling out your money. |
|
Please mail me if you spot an error, omission, or something just plain dodgy. Also take a look at the disclaimer at the bottom of the page :o)
Although every care is taken to avoid errors, neither the site nor myself can be held responsible for any errors or omissions contained on any part of this site.
If you have any queries, good advice from the peeps who have done this before can be had by posting a question on the Fiesta Turbo forums. More information on engine conversions can also be found at Mark Stewart's Fiesta Projects site. |
[links]
Fiesta engine conversions guide
A run-down of the various engines you can fit in your Fiesta to gain the best power. Information also applicable to Puma and Ka.
Zetec tuning guide
What you can do to gain power from your Zetec, right up to 200+bhp 2.0L tuning.
Zetec turbo guide
What you need to know if you want to turbo your zetec engine.
|
| Whether you want to make your car stand out from the crowd or go the stealth route, it all starts here |
| Beauty isn't only skin-deep on cars, and sorting your interior doesn't need to cost loads: click here for ideas |
| Making big power, getting it to the wheels and making sure it doesn't go pop |
| Suspension, brakes, handling tweaks, fitting wheels without rubbing - finishing off the job Ford started |
| You wanna system to crack the back windows? A system that plays DVDs with cinema quality sound? Wanna make your passengers deaf? Thought so. Click here then... |
| Sleep easier at night with our anti-toerag security-tips and product reviews |
| Given up on the car for today? Given up on the car for good? Time for alternative inspiration maybe? Try these suggestions |
|
